Arduino Starter Plus Kit (Custom Starter Kit – Uno R3)

SKU: KIT-03

2,659.00

LOCAL PICKUP @ OUR SHOP! Within Davao City.

P 190 FLAT-RATE DELIVERY! For orders less than 2kg, anywhere in the Philippines.

FREE DELIVERY! For orders more than P 3,000.

 

  • Description
  • Reviews (0)

Description

After gaining knowledge and learning some of the specifications of arduino. The Starter Kit plus  has made for you to enjoy more challenging project with the used of sensors, LCD display, Matrix LED 8×8, micro and data logging with the use of micro SD card.

The Starter PLUS Kit contains:

Arduino Uno R3 Compatible (CH340G) with Micro-USB cable 1
PIR Motion sensor, module 1
Temperature and Humidity sensor DHT11, module 1
Sound Detector sensor, module1
Infrared Barrier sensor — obstacle avoidance, module 1
Micro-SD Card module 1
Relay module, 1 Relay 5V 1
Matrix LED 8×8 module (32x32mm) 1
LCD Display 1602 (2 rows 16 columns) parallel I/O 1
Rotation Potentiometer module (10k Ohm) 1
Micro-Servo Motor 180 degrees (SG-90) 1
Antistatic bag 1
1 set Prototyping Materials (Jumper wires + Breadboard)
Dupont Jumper wire Male to Male 4″(100mm) 10
Dupont Jumper wire Male to Male 8″ (200mm) 5
Dupont Jumper wire Male to Male 12″(300mm) 5
Breadboard Self-Adhesive white 8.3×5.5×0.85cm 1
1 set Resistors
Resistor DIP, 100 Ohm, 1/4W,5% 5
Resistor DIP, 1K Ohm, 1/4W,5% 1
Resistor DIP, 10K Ohm, 1/4W,5% 1
1 set LEDs + RGB LED
LED (Red)LED 3mm, DIP 5
LED (Green)LED 3mm, DIP 5
LED (Blue)LED 3mm, DIP 5
LED RGB (Diffused LED RGB 10mm)

Uno R3 ATmega328:

UNO R3 CH340G/ATmega328 – compatible with Arduino UNO R3 board. Built on the Atmel ATmega328 microcontroller and USB-UART interface chip CH340G. Board for functionality similar to the Arduino UNO (ATmega 28). It is a budget, but the same stable, and uses the original chips Atmel ATmega328 (16 MHz)

arduino uno, uno r3

Temperature and Humidity Sensor DHT11

  • This is DHT11 sensor for measuring temperature and realtive humidity. It is an accurate and inexpensive sensor that includes an analog-to-digital converter (ADC) to convert analog values of relative humidity and temperature.The 8-bit microcontroller in the sensor is used for data conversion.

PIR Motion sensor

This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low.
Item weight7.2 g

Infrared Barrier Sensor Module (Obstacle Avoidance)

The sensor module light is adaptable to the environment, it has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving tube, after the comparator circuit processing, green indicator will light up, at the same time signal output interface to output digital signal (a low level signal), can be through the potentiometer knob adjust the detection distance, effective distance range 2 ~ 30cm, working voltage is 3.3V to 5V. The sensor detection range can be through the potentiometer to adjust and have small interference, easy to assemble, easy to use, etc, can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on many occasions.

The Sound Detector is Sensor module is based on a microphone and a power amplifier. It can be used for detecting the sound strength of the environment. The value of digital output can be adjusted by the potentiometer. Also, can use Analog output to get an analog variable signal.

For Sound Detector has two outputs:
AO – analog output, real-time output voltage signal of the microphone
DO – when the sound intensity reaches a certain threshold, the output high and low signal The threshold-sensitivity can be adjusted via potentiometer on the sensor.

This is a 1 channel Relay module, which can be used to control various appliances, and other equipment with a current not more than 10A (250VAC/60VDC).

relay, module, io control, actuator

 Matrix LED 8×8 

This matrix LED uses Maxim driver IC MAX7219/7221. It has built-in clock to help multiplex the LEDs. Up to eight 8×8′ matrix LEDs can be connected and used on a single I2C bus (or a combination, such as four 8×8’s and four 7-segments, etc).

led, led matrix, displays

LCD Display

This is a basic 16 x 2  (16 columns by 2 rows) on display. Green color.

display, lcd, 1602

Rotation Potentiometer module

The Rotation potentiometer (analog) is a variable resistor for 10KOhm.

 

Micro-Servo motor (SG-90) 180 degrees for Arduino
Speed: Standard speed is 120 degrees, the maximum speed is 180 degrees
Operating Voltage : 4.8~6.0V
Currenct: 0.19A@5V, 0.24A@6V
Operating Speed : 0.12sec/60 degree(4.8V)~0.1sec/60 degree(6.0V)
Torque : 1.6kg/cm(4.8V)
Dead Band Width : 5usec
Temperature Range : -30~+60℃
Cable Length : 25cm
Servo Type : Analog Servo
size:23X12.2X29MM

Reviews

There are no reviews yet.


Only logged in customers who have purchased this product may leave a review.